Sale!

Heltec Relay Smart BMS 4S-240S 500A 7S 8S 10S 13S 14S 16S 20S 32S lifepo4 bms with BT UART 485 CAN for 3.7V 3.2V Lithium Battery Pack

$158.00$355.00

Description

Customize BMS in master-slave design, parallel connection.
Kindly contact us for details before placing an order.

*Product Advantages:

It supports 500A continuous current output, and the peak current can reach 2000A. It is not easy to be heated and damaged. If damaged, the main control will not be affected. You only need to replace the relay to reduce maintenance costs. Current relay power consumption: 250mA.

The relay is a main circuit switch. You can choose different currents, but the maximum current does not exceed 500A. It is recommended that the working power consumption be less than 500mA. BMS only provides 12V control voltage to control the introduction of relay.

1. BMS built-in BT module can be used to view battery parameters on the phone( Android only, IOS is under development ).
*Mobile APP not available for BMS more than 32S and Master-slave design.


2. You can develop your own application system according to your own needs. We can provide BMS interface communication protocol.


3. The main protection functions of BMS are: overcharge protection, overdischarge protection, overcurrent protection, balance protection, short circuit protection, BMS low voltage sleep, NTC temperature control protection, etc.4. The application can adjust hardware and software parameters and support Li ion, LiFePO4, LTO batteries.5. It can be compatible with 3S-32S lithium battery pack. The length of the balanced cable is about 800mm. There are marks on each cable such as B-, B1+, B2+……B16+, B+. This is a very convenient design for welding cables.

6. Static balance: setting the battery voltage difference between 0.02V-0.05V, it will automatically turn on the balance function.

7. Application: large vehicle starting power, solar energy storage, engineering vehicle, low speed four wheeled vehicle, RV or any other device you want to place.

8. The protection parameter settings and modified:
Charge and discharge high temperature and low temperature, battery pack overvoltage and undervoltage, unit cell overvoltage and undervoltage, short circuit and differential pressure value, balance voltage can be modified. It can also reset and restore factory settings.

Warm tips:

* BMS can handle at most 240S battery pack with master-slave design. Battery above 32S is recommend to consider this master-slave design.Kindly contact us for more info.
*We can also provide Charger that CAN communicate with BMS for charging,For more info. kindly contact us directly.

Products details

This is our real project for 110S 352V Solar Energy Storage

This client just want save money choose two package , one is 55S, but it is not good for package or any repair . So if you need high voltage bms system . Just contact us .

For example:
 

If one battery is packed in 16S, and 10 pack in total, it’s 160S 512V battery pack.

Therefore, you need 10 pcs slave bms board and other accessories.

If it’s 64S system,consider two 32S batteries pack in series, the selling price is the same as the 36S. So just select the 36S slave board will be fine.

For more info.of high voltage battery system, kindly contact us in advance
Below is the application of 110S lifepo4 Solar energy storage system (Battery is not included)

 

Details of Relay smart BMS:

 

Suggestion

Below 200A choose 2 Relay is enough

above 200A choose 3pcs relay

if used on like Heavy Truck start up. choose 4pcs relay

Sku details: 

3-4S BMS :  include 1*3-4S BMS with harness + 1*Hall

6-8S BMS :  include 1*6-8S BMS with harness + 1*Hall

10-24S BMS :  include 1*10-24S BMS with harness + 1*Hall

25-32S BMS :  include 1*25-32S BMS with harness + 1*Hall

For high discharge current (250A and above), and string 25S and above , we recommend using pre-resistance and pre-charging relay to work together

If used on same port(charging and discharging share the same port), we recommend using Anti-reverse diode to work together.

 

 

Features:

Voltage requirements 10~20V~55V~120V

Dynamic self-consumption: ≤1.5W

Static self-consumption: ≤50uA

System startup mode: external soft switch signal trigger

SOC estimation difference: ±5%

Balance current: 60mA

Working temperature: -40~85°C

Support battery pack: 3-4S, 6-16S .17-24S

Single string voltage collection range: 0~5V

Single string voltage collection error: ±10mV FS

Total battery voltage collection range: depends on specifications

Total battery voltage collection error: ±100MV FS

Charge and discharge current collection range: >500A

Charge and discharge current collection error: ±2%

NTC temperature control collection range: -40~125°C

NTC temperature control check error: ±1°C

Communication:

1* UART Support Modbus protocol

1*Isolated RS485 interface, support Modbus protocol

1*Independent CAN2.0B interface

 

Ternary Lithium Battery

Overcharge protection: 4.25V

Charge release protection: 4.15V

Charge detection delay: 1000mS

Discharge and power failure protection: 2.7V±0.1V

Discharge release protection: 2.9V±0.1V

Discharge detection delay: 1000mS

Charging current: number of strings*4.2V

Continuous current: 200A~500A

Overcurrent protection: 200A *3-8 Times

Overcurrent detection delay: 3000mS

Overcurrent release protection: disconnect the load

Short-circuit protection: load short-circuit through the protection board (no direct short-circuit BMS)

Charging and discharging temperature: ≥75°C

Reset social equipment: <50°C

Condition range: -20°C ~85°C

Opening conditions of balanced pressure difference: 0.02V-0.05V

 

Lifepo4 Battery

Overcharge protection: 3.65V

Charge release protection: 3.55V

Charge detection delay: 1000mS

Discharge and power-off protection: 2.4V±0.1V

Discharge release protection: 2.6V±0.1V

Discharge detection delay: 1000mS

Charging current: number of strings*3.6V

Continuous current: 200A~500A

Overcurrent protection: 200A *3-8 Times

Overcurrent detection delay: 3000mS

Overcurrent release protection: disconnect the load

Short-circuit protection: load short-circuit through the protection board (no direct short-circuit BMS)

Charging and discharging temperature: ≥75°C

Reset social equipment: <50°C

Condition range: -20°C ~85°C

Opening conditions of balanced pressure difference: 0.02V-0.05V

1.Mobile app ( Andriod system)
The mobile app monitors the battery charge and discharge status, and the single battery voltage, total battery voltage, two-way battery current, temperature display, battery capacity display and protection value are adjustable.
*iPhone is not available now.

**Mobile APP not available for BMS more than 32S and Master-slave design.
2. BMS and PC connection
*Connect the computer program through RS485 to USB module for debugging BMS operation parameters.

3. Provide BMS interface protocol

 
*We can provide CAN communication protocol and RS485 protocol for your use.
*If need us to integrate protocol, kindly send us your protocol to evaluate and we will quote for you accordingly.

 
4.Support SOC Display
*Support current detection, collect current and voltage with high accuracy, and calculate battery capacity through BMS.
5. Temperature sensor

Collect the current temperature of the battery environment in real time, and support the adjustment of high and low temperature BMS power-off function. The product has 3-4 temperature sensors with a length of 500mm.


6. BMS manual switch off
BMS can be switch off manually through KEY line.
Off: Disconnection KEY lines
7. Communication isolation
The CAN, RS485 and UART communication functions of this BMS have isolation and strong anti-interference.8. Battery balance function
Battery assisted static balance, automatically turns on when there is a voltage difference(between 0.02V-0.05V)in the battery, and the balance current is 60mA.

9. New Energy Vehicle Relay
Using 12V weak current control relay to work, can withstand very large current output, and will not heat, even if it is damaged, it is easy to replace.
* Customer can use their own relay

10. Hall sensor

It is used to detect current input and output information, and send the information to BMS to calculate SOC. Overcurrent protection can be set, error 2%, range 600A.

11.Configure harness wiring

The functional position of each wiring harness is different, each cable has a corresponding mark to facilitate customers to identify the corresponding function

12.Wiring Connection

Each product has different connection, kindly contact us for details

 

 

Additional information

Weight N/A
String

, , , , ,

relay

/, relay, relay*2, relay*3

Reviews

There are no reviews yet.

Be the first to review “Heltec Relay Smart BMS 4S-240S 500A 7S 8S 10S 13S 14S 16S 20S 32S lifepo4 bms with BT UART 485 CAN for 3.7V 3.2V Lithium Battery Pack”